Most facilities managers can say how much cleaning costs. Fewer can say whether it is getting better or worse. The usual evidence is a complaint, and by the time a complaint arrives, the problem has been running for days.

A small set of metrics fixes that. This guide covers eight you can collect without special software, how to calculate each one, and what a change usually means. We have left out industry benchmarks on purpose. Targets depend on the building, the contract and the standard you have agreed, so set your own baseline first and measure against that.

Start with a baseline, not a target

For the first four to six weeks, measure and do not act. You need to know what normal looks like at each site before a number means anything. A hospital wing, an office floor and a school will never share a target, and comparing them in a spreadsheet will mislead you.

Pick the same reporting period for every metric, usually a week or a month, and keep it fixed. Use the same definitions across sites.

The eight metrics

1. On-time completion rate

What it measures: the share of scheduled cleans that happened within their window.

How to calculate: cleans completed on time divided by cleans scheduled, for a period.

Why it matters: it is the most direct measure of whether the schedule is being followed. It needs a record of each clean with a time, and a defined window for each area.

When it drops: check whether it is one area, one shift or one person. A single area usually means the schedule is wrong. A single shift usually means a staffing or handover problem.

2. Missed cleans

What it measures: scheduled cleans that did not happen at all, as opposed to ones that were late.

How to calculate: count the cleans with no record by the end of their window. Track the count and the share of total.

Why it matters: late and missed are different problems. Late is a pacing issue. Missed means the area went without service.

When it rises: look for the pattern before the cause. Weekends, holidays and covering for absences are the usual places for missed cleans to cluster.

3. Coverage

What it measures: the share of areas that have a record at all.

How to calculate: areas with at least one logged clean in the period divided by total areas.

Why it matters: an on-time rate can look excellent if the hard-to-reach areas are never logged. Coverage catches the areas that fall out of the system.

4. Inspection pass rate and score

What it measures: how well the work was done, as judged by an inspector against a checklist.

How to calculate: items passed divided by items inspected, per inspection. Report the average and the trend per site. If you use a 1 to 5 scale or APPA appearance levels, report the average level.

Why it matters: a log shows the work was done. An inspection shows whether it was done well. You need both. Our janitorial inspection checklist and scoring guide covers building a checklist that two inspectors score the same way.

When it drops: read the failed items, not only the score. A fall driven by one item, such as restroom floors, points to a training or product fix.

5. Issue count and response time

What it measures: how many problems are reported and how quickly they are resolved.

How to calculate: count reports per period, and measure the time from report to resolution. Report the median, not just the average, because one slow case skews an average.

Why it matters: reports are your earliest warning from the people who use the building. Response time shows whether the team acts on them. Fast resolution often matters more to occupants than a low report count.

When it rises: a rise in reports is not always bad. If you have just added a QR reporting poster, reports rise because it is easier to report. Compare against the same period before and after.

6. Repeat defects

What it measures: the same problem found in the same place more than once.

How to calculate: count the issues or failed inspection items that recur in the same area within a set window, such as 30 days.

Why it matters: a repeat defect means the fix did not hold. It separates a one-off miss from a cause that has not been dealt with, such as a worn fixture, the wrong chemical or an unrealistic time allowance.

7. Supply stockouts

What it measures: the number of times a consumable, such as soap, paper towel or tissue, ran out before it was restocked.

How to calculate: count the reports or inspection findings of empty dispensers in the period.

Why it matters: an empty dispenser is one of the most visible failures to an occupant and one of the easiest to prevent. A rise points to par levels, delivery timing or the restock step in the route.

8. Labour hours and cost per square foot

What it measures: what the cleaning costs for the space it covers, and how many hours it takes.

How to calculate: total cleaning cost for the period divided by cleaned square footage. Separately, track labour hours per site against the hours the scope calls for.

Why it matters: cost per square foot lets you compare sites and contractors on the same basis. Hours against the scope show whether a site is under or over resourced. Our post on janitorial production rates explains how scope hours are worked out.

Watch for: a low cost per square foot can be a warning, not a win. If hours drop and the on-time rate and inspection scores fall with them, the saving is being paid for in quality.

How to read them together

No single number tells you much. Read them in pairs:

  • High on-time rate, low inspection score: the work is being done but not done well. Look at training, tools and time allowances.
  • Low on-time rate, high inspection score: quality is fine when the work happens, but the schedule is not being kept. Look at staffing and routes.
  • Rising issues, steady inspection scores: the inspection checklist may be missing what occupants notice. Review it against the reports.
  • Falling cost, falling scores: hours have been cut below what the scope needs.

Where the data comes from

You can collect most of these on paper, but the effort grows with the number of sites. Three sources do the work:

  1. A cleaning log with times. This feeds on-time completion, missed cleans and coverage. TidyTrack records each clean by area, time and person, and reports compliance by site, area and cleaner. A missed clean raises an alert.
  2. An inspection tool or form. This feeds pass rate and score. TidyTrack does not run scored inspections today, so use your own form or a dedicated inspection tool.
  3. Issue reports. These feed issue count and response time. A QR report poster lets anyone in the building report a problem without an account.

Cost and hours come from your contract, payroll or invoices.

Using the numbers

Review the same short set each month, per site, and write down the one thing you will change. If you manage a contractor, share the numbers with them. They are more useful as a shared record than as a penalty, and our guide to writing a quality control plan shows how to build them into the contract. If you are the contractor, the same numbers become proof of service when a client asks.